Futaba GY Pdf User Manuals. View online or download Futaba GY Instruction Manual. Nstruction, Anual • Read online or download PDF • Futaba GY User Manual. The chart below works for almost all helicopters but you should consult your helicopter manual if you are not sure. Note that I have seen.

| Author: | Nikogrel Vodal |
| Country: | Timor Leste |
| Language: | English (Spanish) |
| Genre: | Love |
| Published (Last): | 2 April 2014 |
| Pages: | 435 |
| PDF File Size: | 12.63 Mb |
| ePub File Size: | 10.27 Mb |
| ISBN: | 581-5-24963-888-9 |
| Downloads: | 92902 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Magul |
Most other receivers have it labeled channel 5.
Because this is on a small heli and I wanted to keep the wiring short I made my own. That will get you yy520 1-blink, hold the button down for 2 seconds to get to 2-blinks, then again for 2 seconds to get to 3-blink.
Make sure when you are adjusting the tail control rod links that you do not get too much of the threads showing.
FUTABA GY Instruction Manual (Page 23 of 32)
Move the Gear switch down position 1. Also make sure that your plugs in the receiver have the correct polarity. In order to be able to post messages on the HeliFreak forums, you must first register. On a larger class 50 size it might be in the 80 to range. Use an exacto knife to shave this off. This is going to vary for different helicopters and different brand servos.
Futaba GY Helicopter Gyro w/Heading Hold |
On the small helicopters a gain of around 50 is normal. Blue – F3C degrees per second Red – 3D degrees per second To change the mode, quickly press and release the button on the gyro. Move gy5200 tail control rod link to the ball. You can set this to what you need. The light on the gyro will turn solid Blue. The blue label on the gyro needs to be either up or manuak.
Back to Main Page. At this time we need to check that the radio is correctly controlling the gyro. Move the rudder stick right and verify the trailing edge of the tail blades move to the right.
Wait three seconds for it to initialize. In a manuwl you will turn on the receiver.
Now that you have found a position for the servo arm you need to mount the ball on it. Heading Hold Solid Blue: Keep the tail control yg520 off of the servo. Release the button and you will see the gyro light repeat a ‘1 blink’.
On the receiver side, you will connect the black lead to the ‘Rudd’ channel and the red lead goes to the ‘Gear’.

Password Please enter a password for your user account. With it in this position the gyro will be in heading hold with the gear switch up position gg520.
Place the servo arm on the servo spline. Hold in the button on the gyro for three seconds. When you move the rudder stick to the right, it will move the trailing edge of the tail blades to the right side of the helicopter. Notice that the values are different, ty520 do not need as much to rotate the helicopter to the left because it is going ‘with’ the torque in that direction. The tail servo will connect to the side that has one socket.
Remove Advertisements Sponsored Links.
![]()
If you do not have a hole exactly 90 degrees then take the servo arm off and rotate it to another position. The black wires of every plug all should be on the same side of the receiver.
Options Quote message in reply?
Futaba GY520 Helicopter Gyro w/Heading Hold
Power up the radio and the receiver. You will see the servo move to one side. So it is important to make the checks on the bench so you do not risk damaging the helicopter.
Note that I have seen common problems with the tail blades grips flipped the wrong direction and the tail belt twisted the wrong direction. Check the holes in the arm for one that is 90 degrees to the tail control rod.
Watch the light on the gyro, when you move the rudder stick from center, the light needs to change from a solid color to a flashing violet. If the nanual does not feel solid and lets go when in a high load then increase the gain. The light will change to a violet color. Look at the picture on the right. When you power up the gyro for the first time you should have the tail servo disconnected.
