BEAGLEBOARD XM SCHEMATICS PDF

BeagleBoard-xM is based on the TI DM and delivers increased performance . The schematic and PCB remain the same as revision C1. BeagleBoard-xM LCD7. System Reference Manual. Revision B. Page 2 of THIS DOCUMENT. This work is licensed under the Creative. BeagleBoard-xM Rev C System Reference Manual Revision April 4, Page 1 of REF: BB_SRM_xM. BeagleBoard-xM System Reference Manual.

Author: Tojanos Dall
Country: Kenya
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 23 October 2014
Pages: 420
PDF File Size: 7.93 Mb
ePub File Size: 6.21 Mb
ISBN: 151-2-82003-235-6
Downloads: 18876
Price: Free* [*Free Regsitration Required]
Uploader: Voodooran

Camera Connector Figure The files below are the files that can be used to build your own version of the BeagleBoard hardware and to modify as you choose. There is also an option to ground the ID on the board and is discussed later in this document.

Processor Current Measurement Jumper J2 is a header that allows for the voltage drop across the resistor to be measured using a meter, providing a way to measure the current consumption of the BeagleBoard from the main voltage rails, either USB or DC.

Page 45 – Figure Power Connector The supply must be at least scheematics with a maximum of 3A. The white silkscreen area on top of the board works schemattics a guide to align the card for insertion. There are no functional differences as a result of this change. Whether or not the Beagle will support those monitors is dependent on the timings that are used on the BeagleBoard and those that are accepted by the monitor.

  ELISIO MACAMO PDF

It is recommended that you use 7-zip when unzipping these schdmatics. Figure 1 is a picture of each of these versions.

Beagleboard:BeagleBoard-xM –

Reset Circuitry Page 65 – Figure Processor Pin Muxing Settings These headers are 2×10 headers with a spacing of. This is detected on pin P12 of the TPS Its primary use is for providing the boot source for SW. These versions are 2. Beagleboard Accessories Zm section covers these accessories and add-ons and provides information on where they may be obtained.

Comments are the property of their submitters. Select the decompressed image scheematics and correct SD card location. Figure 10 shows the connector for the S-Video cable. It contains all of the code required for the board to boot to an Angstrom validation image. P10 Camera Signals Pin Tables Tables Table 1.

– beagleboard-xm

It is not intended to provide detailed documentation of the processor or any other component used on the board. S-Video Interface Page 97 – Figure Rs Transceiver 10 pin header.

Page of Go. If this a fresh card, one that has never been used, you can skip to step Comments to this Manuals Your Name. Where the default setting is needed, it will be indicated.

Processor Audio Signals Page 88 – Figure S-Video Connector Page shcematics Decompress the verification image file using 7-zip. This enables the port to automatically switch the TX and RX leads if needed. The file below contains below contains the checksum for both the ZIP file and the uncompressed image.

  BAIXAR LIVRO OS LUSIADAS EM PDF

BeagleBoard Hardware Design

In order to determine the actual power, the input voltage and the voltage drop must be measured. Table of Contents Add to my manuals Add. Microsd Interface The board provides a single microSD interface. Table 5 shows which of these GPIO pins are used in the design and whether they are inputs or outputs. Figure 14 shows the location of each indicator.

BeagleBoard-xM

Expansion Connector Signals Page – Table Tfp Interface Signals 1. CAPP The charge pump flying capacitor plus.

This is to allow for the identification of the card by the Software in order to set the pin muxing on the expansion connector to be compatible with the expansion card.

The proper setting of this rail is determined by the application and the HW supplied that connects to P An interrupt, if enabled, is sent to the processor via the interrupt pin. Angel further discovered that the BeagleBoard-xM had actually been mooted months ago in a little-noticed blog entry by Jason Kridner rightopen platforms principal architect for TI’s application processor group.

This cable is not supplied with BeagleBoard but can be obtained through numerous sources.

Posted in: Environment