ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

| Author: | Sagor Felmaran |
| Country: | Madagascar |
| Language: | English (Spanish) |
| Genre: | Software |
| Published (Last): | 2 February 2018 |
| Pages: | 238 |
| PDF File Size: | 15.89 Mb |
| ePub File Size: | 8.49 Mb |
| ISBN: | 927-2-57853-326-6 |
| Downloads: | 46928 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Mikadal |
Your comments will receive careful consideration at a meeting of the responsible technical asstm, which you may attend. Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the aatm. NOTE 2—The industry de?
Last previous edition A — Over 12 Through 11? It is normally produced as a fully killed steel. Each of the elements listed in Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis.
The material must be adequately protected and correctly identi? Notwithstanding the absence of a signature, the organization submitting the document is responsible for the content of the document. Elements such as aluminum may be added in sufficient amounts to control the austenitic grain size.
NOTE 1—Camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge.

For strip length under mm, camber tolerance shall be subject to negotiation. Materials and Manufacture 5. A number in parentheses indicates the year of last reapproval.
ASTM A682 Grade 1074
Finish and Edges Zstm of this standard are expressly advised that determination of the validity of any such patent ast, and the risk of infringement of such rights, are entirely their own responsibility. Strip is classified as product that is 0. This is produced when the edge condition is not a critical requirement for the? Combining values from the two systems will result in nonconformance with the speci?
Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of production.
However, under SI the preferred term in mass. When the amount of copper, nickel, chromium, or molybdenum atsm less than 0. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values.
The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. NOTE 2—Camber tolerances as shown in the table are for any mm length.
For strip length under 8 ft. Rework and Retreatment When the amount of vanadium, columbium, or titanium is less than 0.

Note 1—The term weight is used when inch-pound units are the standard. Strip tolerance products may be available in widths wider than ? When agreed by purchaser and supplier, other silicon ranges are permissible. Axtm any of the retests fail to comply with the requirements, the coil shall be rejected.
ASTM A, AM_百度文库
Conformance to SI tolerances is mandatory when the “M” specification is used. C When edge, width and thickness are not de? The results of analyses taken from different pieces within a heat may differ from each other and from the cast analysis.

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Dimensions, Mass, and Permissible Variations 9.
Strip is classified as product that is 0. C When the chromium is speci? Within the text, the SI units are shown in brackets. B Measured 10 mm or more in from edge; and on narrower than 25 mm, at any place between edges.
