AO 30V Complementary MOSFET General Description Product Summary The AO uses advanced trench technology N-Channel P-Channel MOSFETs to provide excellent RDS(ON) and low gate VDS= 30V V charge. N-Channel:VDS=30V ID=6A RDS(ON) < 30mΩ (VGS = 10V) RDS(ON) < 42mΩ. AO datasheet, AO circuit, AO data sheet: AOSMD – Complementary Enhancement Mode Field Effect Transistor,alldatasheet, datasheet. AO Complementary Enhancement Mode Field Effect Transistor. AO Complementary Details, datasheet, quote on part number: AO

| Author: | Mirn Tekree |
| Country: | Uruguay |
| Language: | English (Spanish) |
| Genre: | Art |
| Published (Last): | 22 May 2011 |
| Pages: | 123 |
| PDF File Size: | 9.11 Mb |
| ePub File Size: | 1.41 Mb |
| ISBN: | 396-6-44006-380-5 |
| Downloads: | 37655 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Tygolkis |
![]()
I checked between gate and drain, source and drain I will get back to you with the results. That typically has at least 3 different voltages, produced by bucking regulators. I have a P that powers up fine.
AO4606 Datasheet PDF
Originally Posted by Welchs SO this leads me to ask the question I am thinking the power supply card is fine but the video processor board is acting up. Originally Posted by Welchs thanks!!!!!! I looked datashet the fuse and connector advise datashdet could not find any issues. Thanks for the help and sorry for taking so long and the incomplete info.
I did attach photos of the front and back of it.

Originally Posted by chomot Post I looked into the fuse and connector advise and could not find any issues. Does anyone know of any issues with these. Since I am a one trick pony on these I orderd a set of caps and replaced them hoping for the best. I started with the voltage across the big filter cap I have a KDS P monitor which does not work.
All it is is four buttons and an LED. I was looking at the signal board wich I also included a photo of and doing some searches on it but I could not find any silver bullet type fix for it. It is usually capacitively coupled. Should ALL of the inputs on the primary side be shorted?
How did you know the part number is AO? I also measured the diode as shown in the data sheet. One end to the circuit while the other to the transformer pin.
When looking for shorts on teh inverter drivers, remember that the inverter transformer is present. I see no obvious issues visually. Right now, when i power it up None of the buttons on the bottom work except the power on and off.
I have fixed a lot of monitors by replacing the caps on the PS card but this will be my first with processor card issues. So i guess the chips are ok. I found one cap “near” the big filter cap which was “bad”. I guess I will replace the four uf ai4606 25v, two uf x 25v and the one uf x 25v and see where that takes me.
Anyway this one has the good brand of Samxon for all but the big guy and that is a KM M but they rarly go bad from what I know. If you have 5V ao466 12V, check the logic board. I replaced this cap.
![]()
Originally Posted by Welchs Right now, when i power it up Have you seen this before? Thanks for the help, I did add a few pics of the board in case you can see something I do not. The only button that works is the power and all the others do not give me any menu nothing. Originally Posted by chomot Post I know this is an old thread datashdet I figured since there is good advice here on the P I should see if my problem will ao406 to it. The rest of the buttons produce no set up or adjustment windows and I can see no video from my PC at all.
The monitor is full bright all day long.
AO Datasheet(PDF) – Alpha & Omega Semiconductors
Originally Posted by Welchs You really think the burnt spots are just due to bad solder joints? Also sorry for not mentioning that I did look at the panal when you brought it up, I should have said so but I forgot since I did not see anything about it. Can you tell from the data sheet if D2 and D1 are shorted?
So i will have to look a little deeper.
